No products in the cart.
OUXI V8 Electric Bike Display Settings
- “Power” (Mode) – Power on/off (press and hold)
- “+” (Up) – Raise pedal assist level
- “-” (Down) – Lower pedal assist level
What Can I Do with Ebike Display Setting
There are three buttons on the OUXI V8 Ebike display: Power, + and –, allow riders to adjust multipal functions as how your V8 ebike operates:
Cruise control; Zero-start / push-start; Driving mode from totally Pedal Assist to Throttle Assist; Speedometer units (mph/kph), Release the Maximum Speed or the like.
How to Access & Change Display Setting
- Turn on the V8 ebike: Press and Hold the Power button on the controller until the display appears and you’re ready to go.
- Access V8 bike display setting: Press and Hold + & – key to enter Mode Settings.
- Toggle through display P setting parameter by pressing the Power button. Press the + or – key to raise or lower the required values.
- Save your modified setting by Switching to the next parameter; Or press & hold + & – key to exit the display settings interface. Also you could wait 8 seconds to automatically confirm and save settings.
Display Function Description
- Display Functions
Speed display, power indicator, fault indication, total mileage, single trip mileage.
- Control / Setting Functions
Power switch, wheel diameter setting, sleep time setting, display brightness setting. Start mode setting, drive mode setting, voltage level setting, controller limit value setting.
- Communication protocol:UART
All contents of the display screen (full display in boot 1S)
AVG: Average speed; MAX speed; SPEED: Current speed; mph | km/h
V8 Ebike power gear, 0-9 digital and file bar display
V8 eBike Status
Battery capacity level; Motor failure; Brake alarm; Headlight
Total mileage ODO; Single mileage TRIP; Boot TIME; Battery voltage VOL
V8 Electric Bike Error Code
Fault code description
Battery under-voltage alarm
Communication reception failure
Communication send failure
V8 Ebike Display Setting
Display Background brightness; Luminance level 1 to 3 = darkest to brightest
Mileage unit of distance, switch between Kilometers and miles. 0=KM; 1=MILE
Voltage grades: 24V, 36V, 48V, 60V, 64V default 36V; The battery and the kit voltages must be the same! (V8 electric bike = 48V)
Sleep timer: 0 = LCD screen will never go off for energy save mode; Other numbers stand for the sleep time (1-60 min)
PAS Grades: 0 – Has 3 grades mode: 1 grade 2V, 2 grade 3V, 3 grade 4V
Wheel Size: unit, inch; Precision: 0 | 1;
Speed measuring magnet: range 1-100
Speed Limit: Range 0-100 km/H, 100= No speed limit,
Zero start & kick start setting, 0 = zero start; 1 = Non-zero start; Zero start (0) will engage the motor instantly jump forward while your bike is at a standstill; Non-zero start (1) will give some delay when you throttle, throttle will only works when your bike is moving.
Drive Mode setting. This setting could come in very handy. This P setting allows you to turn off the throttle completely.
PAS sensitivity setting, range: 1-24; This setting means respond time when you want the motor to start assist based on how many pedal rotations you do. Set the sensitivity carefully, 1 is the most sensitive.
PAS start intensity, This setting tells the motor how strong pedal assist you want it. setting range: 0-5; The lower value provides a little assist when you start pedaling.
PAS Magnet Type, three setting 5, 8 and 12.
Controller limit value set default 12A range: 1-20A
ODO Zero-Out: Reset the odometer back to zero by long press + key for 5 seconds
Cruise Control. 0 = No enabling cruising, 1 = enabling cruising; Automatic cruise optional (valid for protocol 2 only)
Display speed ratio adjustment range: 50 % ~ 150 %
0 power bit, 0: 0, 1: does not include 0